T1000 CONTROL SOFTWARE
RELEASE NOTES

v2.0.1.56 (9/11/2012)
- NOTE:  Upgrade to 3492 must be done before this version is installed!!!  All the changes that
  needed to be done in the 3492 release need to be done before this version is installed.
- Changed references to INX to EFI.
- Changed references to T660, T660UV, T1000UV to T1000.
- Fixed left/right edge crop bug.
- At startup, GUI now waits for the home carriage to finish before going live.
- At startup, GUI now asks to home the gantry if it's needed and waits for the home to complete
  before going live.
- Updated white alignment prints to include W1 & W2 labels.  NOTE:  On the 12x3 white color-to-color
  forward and reverse prints, the white layer prints before the black layer.  This was done to help
  with white nozzle dropout
- Updated headdefs.config in default installer to have voltage adjustments.
- Added constants.config back into list of configs copied at install from previous versions.
- Extended the gantry profile closer to the front of the table.  NOTE:  Profile Gantry must be done
  after this install (remember to quit and restart the GUI for the new gantry profile to take effect)
  followed by setting of the gantry orthogonality using the Orthogonality.ism alignment print.
- Removed empty white buttons on the maintenance tab (didn't work on the T1000).
- Fixed window size problem

v1.0.1.3606 (5/23/2012)
- removed HASP key support

v1.0.0.3490 (12/15/2011)
- Swaps the sense of the recirculate/ink fill valve (must only run on printers with the tubing swapped).
- Recirculation turned back on.

v1.0.1.3489 (12/15/2011)
- Prints out firmware rev #s on startup.
BUG FIXES
- Win7 set to European #'s should not cause bad numbers coming from the Galil board.

v1.0.1.3403 (10/20/2011)
BUG FIXES
- Loading non-existent bulb modes should no longer crash the application.
- Lamp open/close ranges have been adjusted to stop flickering.

v1.0.1.3389 (10/6/2011)
BUG FIXES
- White recirculation has been disabled again.
- An updated constants.config file with a fix for a potentially invalid bulb mode has been included.

v1.0.1.3368 (9/21/2011)
BUG FIXES
- White recirculation is enabled by default.

v1.0.1.3364 (9/20/2011)
BUG FIXES
- Copying alignments from 3x3 to 3x6 should work correctly.
- Bidirectional alignment should be more consistent.

v1.0.1.3004 (1/5/2011)
BUG FIXES
- Reverse-direction prints are now positioned correctly.
- Prints with multiple horizontal copies should no longer lag excessively.
- Updated alignment prints have been added.

NEW FEATURES
- The "Layout" tab now correctly shows the approximate position and size of a print with relation to the table.

KNOWN ISSUES
- When upgrading from previous versions, it may be necessary to use the HeadDefinitionConfig.exe tool to add missing entries to the headdefs.config file.  It can be used thusly:

1.  Make sure the control program is NOT running.
2.  Run the tool from inside the "bin" directory.
3.  You'll see a row for each head in the headdefs.config file.
4.  In the "RowIndex" column, set all of the non-white heads to be 1.  The white heads should stay 0.
5.  Exit the program (it saves automagically).

v1.0.1.2856 (10/1/2010)
BUG FIXES
- In some cases, placing a print at the extreme top edge of the table could cause the print to fail after a few passes.  This has been fixed.  Printing at the extreme edges of the table can, in some cases, still cause the gantry to run into the end blocks, so caution should be taken when placing prints.
- Vertical copies are working properly.

NEW FEATURES
- New masks have been created for all print modes.
- Prints are now modified on the fly by named quality settings.
- Several configuration files have had major changes made, and several new files have been added.
- The white heads now have separate temperature settings from the CMYK heads.

KNOWN ISSUES
- The temperature settings for white have not been completely tuned.  As such, the white heads may overshoot their target by several degrees.  The temperatures will stabilize after a short period.

HARDWARE COMPATIBILITY
This release will ONLY work with the new pump board (99-11020-A) and the new heater board (99-11037-C).

v1.0.1.2588 (8/13/2010)
KNOWN ISSUES
6x6 4-pass and 12x9 6-pass print modes will not look correct, owing to mask changes that have not been addressed.
When printing backwards (in a white-under file), avoid placing the print at the extreme top edge of the table to avoid running the gantry into the end blocks.